Bestway - Live It Up

58401

Flowclear™ 1000gal Sand Filter

Product Description

* 110-120V~ , 2.4A
* Pump’s water flow rate (pump capacity ): 3,785L/h (1,000 gal./h)
* Integrated pool system water flow rate (system flow rate): 3,407 L/h (900 gal./h)
* Durable, corrosion-resistant filter tank
* 6-position valve for easy control
* Top flange clamp design allows 360 degree rotation for easy installation
* Easy-to-read pressure gauge
* Strainer for separating leaves and other rough debris
* Easy-access assembly makes service simple
* Package also includes adaptors for pool valves with an outer diameter of 3.8 cm /1.5''
* Both hoses (diameter 3.8 cm /1.5'', 3.2 cm /1.25'') can be used with sand filter (needs to include thread)
* Compatible with most above ground pools
* Sand not included
* Required sand size: #20 silica sand, 0.45-0.85mm, approximately 18kg
* 1,100-27,200L (300-7,200 gallon)pools
* Full color box
* 1 Ea., 13.1 kg (28.8Lb.)
* Contents: One sand filter set

Where To Buy

We are here to support you with everything!

FAQ

User Manual

Find out General FAQs

Assembly

Can I use playground sand or beach sand inside Bestway Flowclear Sand Filters? Close Me

No. Playground sand, beach sand and other similar sands contain impurities and their grain size is not uniform.

What is the recommended size of sand for Bestway Flowclear Sand Filters? Close Me

The recommended size of sand for Bestway Flowclear Sand Filter is from 0.45 mm to 0.85 mm. The most common type is Silica #20, which is available from pool suppliers and many mass merchandisers. Using the incorrect size of sand will cause the system to malfunction and void its warranty.

What tools will I need to assemble the sand filter? Close Me

You will only need a screwdriver to assemble the sand filter.

Why does the pump have to be under the water level? Close Me

The filter pump/sand filter is designed to be positioned on the ground. If the filter pump/sand filter is positioned at (or above) the water level, the motor will work without water. This will cause the filter pump/sand filter to be damaged.

Information

Can I leave the filter pump/sand filter outside while it's raining? Close Me

Yes, you can. But we suggest to not use the pump when it is thundering or lightning.

Can I use my Flowclear filter pump with bigger models of pools, and what should I do? Close Me

First you have to check if the flow rate of your pump is suitable with the water quantity of the new pool, and then you have to make sure the hose connections are compatible.

Can the Sand Filter with Ozonator work without the Ozon function? Close Me

Yes, the sand filter can work without the Ozonator. You have to place the timer on position 0.

Can we use the pool while the filtration system is operating? Close Me

No, please do not use the swimming pool when the filtration system is operating.

How can I set the correct operation time of my Flowclear Sand Filter with Ozonator? Close Me

Consult the Owner’s Manual section for the operating time table with Ozonator.

How does the sand filter work? Close Me

The water from the pool flows through the strainer, up through the control valve, down through the sand, up through the collector hub in the center and out through the control valve back to the pool. Dirt and debris from the pool water are trapped in the sand and clean water is returned into the pool.

How does the timer on the Sand Filter work? Close Me

The timer on the sand filter has 9 different positions. Each position has different cycle. You can leave the sand filter connected to the power source, and the sand filter will operate automatically following the cycle you set: Position 0: Off position (only available from 2024, without on/off switch) Position 4: working time 4 hours / waiting time 20 hours (cancelled from 2024, replaced by position 0) Position 6: Working time 6 hours / waiting time 18 hours Position 8: Working time 8 hours / waiting time 16 hours Position 10: Working time 10 hours / waiting time 14 hours Position 12: Working time 12 hours / waiting time 12 hours Position 24: Working time 24 hours the below three positions are the automatic cycle, and it means that if you set one of these positions, the sand filter will continuously operate following the cycle. Position P4: Cycle working time 4 hours / waiting time 4 hours Position P6: Cycle working time 6 hours / waiting time 6 hours Position P8: Cycle working time 8 hours / waiting time 8 hours

Is it possible to use a timer with my sand filter? Close Me

The timer cannot be used if the sand filter is equipped with an external RCD or GFCI. The timer will compromize the functionality of the products. If the sand filter doesn't have an external PRCD or GFCI, you can use the timer. If you installed the sand filter together with a chlorinator or a pool heater, be sure the chlorinator has already finished the set cycle or switch off the pool heater before the sand filter.

What are the functions performed by the sand filter? Close Me

Bestway Flowclear sand filters have 6 functions: 1. Filter: This function is used to filter pool water and should be positioned here 99% of the time. Water is pumped through the sand filter, where it is cleaned and returned to the pool. 2. Backwash: This function is used to clean the sand bed. Water is pumped down through the collector hub, upwards through the sand bed, and deposited out of Port D. 3. Rinse: This function is for initial startup, cleaning, and sand bed leveling after backwash. Water is pumped downwards through the sand bed, up through the collector hub and deposited out of Port D. 4. Drain: This function drains water from the pool. Another filter bypass setting, water is pumped and deposited out of Port D, instead of returning to the pool. 5. Circulate: This function circulates pool water bypassing the sand filter. Use this function if the filter is broken to collect debris in the debris screens. 6. Closed: This function stops water flowing between the sand filter and the pool.

What causes my guarantee to break? Close Me

The legal warranty doesn’t cover damages due to actions not assignable to the seller/manufacturer, to improper or not normal use of the product by the consumer, or to actions contrary to warnings or instructions written in the user’s manual.

What is the correct pump size for my pool? Close Me

To define the correct size of filtration system for Bestway's Above Ground Pools, you need to know the water capacity of your pool. You can find this information on the package.

Where can I find Bestway instruction videos? Close Me

You can find instruction videos on www.bestwaycorp.com in the support section, or on the Bestway YouTube channel.

Where can I find Bestway User Manuals? Close Me

You can find Bestway User Manuals on www.bestwaycorp.com in the support section.

Where do I find the Serial Number? Close Me

The serial numbers on our products are located in various positions and come in different formats. Please consult the provided guide for details.

Why is the sand flowing into the pool? Close Me

1. The sand is too thin and can pass through the skimmer. Please make sure that you are using the recommended size of sand: 0.45 mm to 0.85 mm. 2. The quality of the sand is not suitable to be used with the filtration system of the swimming pool. 3. The skimmer is damaged. 4. The rinsing was not long enough after the backwash. Please consult the owner's manual to perform the correct operations.

Why is there condensation inside the pressure gauge? Close Me

To read the working pressure of the sand filter, the water goes through the pressure gauge. The condensation is created on the external surface of the pressure gauge due to the difference between the temperature of the water in the pool and the external temperature. Thanks to the high quality of the pressure gauge, the condensation doesn't influence the normal operation of the sand filter.

Maintenance

How do I clean my pool with the Deluxe Kit and Sand Filter on a pool with 3 connections (A-B-B)? Close Me

For pool cleaner: 1. Assemble the pool cleaner, and assemble hose adptor to the end of the hose. 2. Immerse the hose of the cleaner into the water to exhaust the air in the hose. 3. Remove the stopper of the pool and connect the hose adaptor to port B of the pool. 4. Before starting the pump, open the strainer cover to purge all residual air inside the sand filter pump. For pool skimmer: 1. Connect the hose to the adaptor. 2. Assemble the pool skimmer. 3. Connect another end of hose to the bottom of skimmer. 4. Fix the skimmer to the frame of pool, adjust the skimmer body into the water with 5-10cm depth from water surface. 5. Insert the skimmer adaptor to the port B of pool. 6. Before starting the pump, open the cover to purge all residual air inside the pump.

How do I clean the Polysphere™ Pool Filtration Balls? Close Me

The Polysphere™ Pool Filtration Balls look like cotton balls and can be used in all Bestway sand filters, making filtration easier and faster. It is an extremely efficient way to keep pool water clean as an alternative to sand. They are 100% PET material made of non-toxic material and offer better results. You must ensure the pump is unplugged before any maintenance. For cleaning and maintenance: 1. Do not use washing machines to wash Polysphere™ Pool Filtration Balls. 2. Hand wash only; if Polysphere™ Pool Filtration Balls remain soiled or discolored, replace them. 3. Check the status of Polysphere™ Pool Filtration Balls every 4 weeks.

How do I use the regulator? Close Me

1.When used with pumps with the flow rate: 3,000 gal./h (11,356 L/h), turn the top knob until the bottom reaches Line 1. 2.When used with pumps with the flow rate: 2,200-2,500 gal./h (8,327-9,463 L/h), turn the top knob until the bottom reaches Line 2.3.When used with sand filters with the flow rate: 1,500 gal./h (5,678 L/h) or filter pumps with the flow rate: 2,000 gal./h (7,571 L/h), turn the top knob until the bottom reaches Line 3.

How long should I run my filter pump every day? Close Me

We recommend to run the filter pump/sand filter minimum 8 hours every day; this is the necessary time to circulate the entire pool water. The increase of the operating hours depends on the quality of the water or how often the pool is used.

How often I should perform Backwash and Rinse in Bestway Sand Filter? Close Me

Bestway's sand filter is equipped with a pressure gauge that shows the working pressure. If it reaches the red level, it means that the sand is full of debris, and the backwash function must be performed for 5 minutes. After that, rinse for 2 minutes. Important: backwash and rinse functions reduce the quantity of water in your pool, so remember to refill the water to have the correct level of water inside the pool.

How often should I change the sand in my Sand filter? Close Me

Under normal operating conditions, we suggest replacing the sand every year, unless different specifications from the producer.

The reading on Pressure Gauge is higher than the recommended pressure, what can I do? Close Me

If the pressure reading on the pressure gauge is over the maximum pressure mentioned in the user manual, it could be the time to clean the sand. Before cleaning the sand, check the following: - If there is anything blocking the hoses - If the connection valves are closed or partially closed - If there is any hole on the hoses - Turn off the sand filter and check if the pressure goes to 0 After having checked the above conditions, please follow the instructions on the manual to perform backwash and rinsing. If there is still a high-pressure reading, sand bed replacement is necessary.

Which is the correct operation to change the sand in Bestway® sand filters? Close Me

Please follow these steps to replace the sand: First step: switch off the sand filter and unplug the socket from the power outlet. Second step: put the stopper inside the pool to close the valve. If the pool has connection valves, close them. Third step: disconnect the hoses that connect the sand filter to the pool. This will make it easier to remove the sand. Fourth step: open the drain valve on the bottom of the sand filter to drain all residual water into the sand filter body. To speed up the operation, position the control valve between two functions. Fifth step: Open the top flange of the control valve and take it off. Sixth step: Take out all old sand from the tank and rinse with a garden hose to be sure it is clean. Seventh step: Fill with the new sand until it reaches the mark between Max. and Min. marked on the hub. IMPORTANT: cover the hole on the top of the hub to avoid the sand going inside, and add the sand gently to avoid damaging the debris screen at the bottom of the tank. Eighth step: Install the control valve and fix the top flange to close the tank. IMPORTANT: when performing this operation, please be sure that the O-ring is in the correct position and completely clean from the sand. IMPORTANT: Every time you change the sand in the sand filter, before using with the pool, you must perform the backwash and rinse following the instructions provided in the manual.

Why isn't water flowing between the pump and the pool? Close Me

If there is no flow between the pump and the pool follow these steps: 1. Be sure that the socket has power and the switch on the pump is in the on position. Put your hand on the pump to feel the vibration of the motor. 2. See if there is anything that blocking the hoses. 3. Check if the control valve is positioned on the filter function. 4. Perform the backwash and rinse functions. Open the cap on the Port D and be sure that water flows out with power. 5. If all of the above operations function and the problem still remains, it is the time to replace the sand.

Manual	Language
1000Gal. Sand Filter Manual.pdf	Dutch,English,French,German,Portuguese,Spanish
Polysphere Instruction.pdf	Dutch,English,Finnish,French,German,Greek,Hungarian,Italian,Polish,Portuguese,Russian,Spanish,Swedish

We are here to support you with everything!

Find out General FAQs

Recently Viewed